Remote Monitoring for your vessel
Protect your vessel from near or far with the Garmin OnDeck Monitoring System Hub. The always-on connection has the potential to keep you in contact with your vessel from just about anywhere via the Garmin ActiveCaptain app. Track, monitor, and control up to 5 switches on your boat with this fully integrated remote connectivity solution.
Easily access and monitor your vessels battery status, bilge activity, onboard security system, GPS location and more right from your phone. Within the Garmin ActiveCaptain app, you can quickly set up alarm notifications to receive updates of any changes that may threaten your boat or your security system has been triggered. An internal GPS sensor within the GTB 10 HUB allows each user to set up a virtual geofence that will alert you once your boat exits this perimeter.
Seamless integration with a Garmin MFD via ethernet on a Garmin marine network or via NMEA 2000 to other onboard sensors make the OnDeck Hub an easy addition to any electronics setup. Safely and securely collect and store vessel data that the OnDeck Hub obtains via a Global 3G/4G covered network in a cloud for up to 30 days (subscription sold separately and required). If the boat loses power or the battery is disconnected, the OnDeck Hub can last up to 48 hours on it’s own internal backup battery keeping you informed even in critical situations.
Please note, a subscription is required and the OnDeck is compatible with the following Garmin MFD series
- GPSMAP 8400/8600 MFDs
- GPSMAP 7400/7600 MFDs
- GPSMAP 10x2/12x2 Series
- GPSMAP 7x2/9x2/12x2 Plus Series
Click Here for Subscription Details
- Garmin OnDeck Hub
- Door, Temperature and Shore Power Sensors
- Relay Switch
- Power Cable
- 19 Pin In/Out Data Cable
- Marine Network Cable
- NMEA2000 Drop Cable and T Connector
- Two Year Warranty
- Remote Connectivity with Configurable Alarms
- Track, Monitor and Control up to 5 Switches
- Up to a 48 hour internal backup battery
- Full Integration with Garmin Marine Electronics
- Size: 9.1"W x 1.9"H x 5.6“D
Product Accessories for Garmin OnDeck Hub System
Garmin Marine Network Cable (6').
The Garmin NMEA 2000 Starter Kit comes with all of the parts you need to start a NMEA2000 Marine Network.
This cable can be used as your NMEA 2000 backbone or drop cable. Length 2 Meter
Garmin Marine Network Cable (20').
The Garmin NMEA 2000 T-Connector is required for adding components to your network. It is installed on the backbone cable and uses one end of the T-Connector for the drop cable.
Garmin NMEA 2000 Multiport T-Connector.
Garmin GA 38 remote gps antenna with 30' cable. Fits standard 1" marine mount.
This Garmin cable can be used as your NMEA 2000 backbone cable. Length 10 Meter. This cable can not be used as a drop cable.
This Garmin cable can be used as your NMEA 2000 backbone or drop cable. Length: 6 Meters.
The Garmin Marine Network Cable Connector gives you the ability to wire on the connector after you have run the cable through your boat. Sold in a pack of two.
The Garmin NMEA 2000 Female Terminator is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.
Garmin Marine Network Cable (40').
Connect 2 Marine Network cables end to end with the Garmin 010-10580-00 Cable Coupler.
The Garmin NMEA 2000 Male Terminator is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.
Garmin's GT10 Thru Hull Temp sensor provides accurate temperature readings from -13°-140°F in your baitwell, livewell or the waters your fishing. Simple Plug and Play integration with your NMEA2000 network.