Make Your Time on the Water More Enjoyable
The Raymarine Evolution Autopilot System combines advanced aerospace guidance technology with Raymarine’s marine autopilot expertise to provide a new level of autopilot control and reliability. Raymarine has over-shot the expectations for sure making the Evolution Series one of the most advance Autopilots on the market yet keeping the interface as intuitive to operate as any other.
Evolution autopilots employ what engineers at Raymarine call Evolution “AI Control” Algorithms, which enable them to “perceive their environment” to instantly calculate and “evolve” a set of steering commands maximizing performance. The result is precise and confident course tracking, regardless of vessel speed or sea conditions keeping cash in your pocket and not at the fuel dock.
Setting-up an Evolution Autopilot takes around 30 seconds because there is no calibration required. First select the boat type – large power, small power, or sail; then select the drive type – hydraulic, mechanical, or outboard; finally you’ll choose the performance level – performance, cruise, or leisure. It’s just that easy to get setup and you’re ready to hit the open water.
At the heart of the Evolution autopilot system you’ll find the ultra-compact, EV sensor core which is a 9-axis heading sensor and full function course computer all in one. The EV is about the size of a typical marine GPS sensor and can be either bracket-mounted or flush-mounted horizontally. The durable sensor is built to IPX6 and IPX7 standards; and with superior engineering put into the EV’s design it can be installed above or below decks.
A SeaTalk1 to SeaTalk NG Converter Kit (RAX22158) may be required to connect to Earlier or Retired Raymarine Equipment.
Raymarine Software version 1.21 is also a minimum requirement.
- Simple Installation and Setup
- Leisure, Cruising and Performance Modes for Flawless Operation
- Precision Accuracy Within 2 Degrees No Matter the Sea Condition
- Increased Mounting Options to Suit Most Any Make or Model Vessel
- SeaTalk NG Connectivity To Easily Network With New and Most Earlier Raymarine Setups
Product Accessories for Raymarine Evolution EV200 Autopilot
Si-Tex Hydraulic Autopilot Hose Kit with Fittings, Part Number OC17SUK42.
Raymarine SeaTalk Ng to DeviceNet (NMEA2000) Female Adapter Cable
This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 400mm.
This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 5 Meter.
Raymarine Converter kit allows select SeaTalk 1 devices to interface and communicate on the SeaTalk NG data network. Plug and Play insallation.
Raymarine's 5-Way Connector is designed to connect 3 drop cables and 2 terminators.
Raymarine SeaTalkNG T-piece connector.
This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 1 Meter.
The Raymarine SeaTalk NG Starter Kit includes all the pieces necessary to create a SeaTalk NG network on your boat.
The Raymarine Type 1 Pump for Autopilots is a 12 volt reversing hydraulic pump for use with boats with steering system fluid capacity of 4.9 cubic inch to 14 cubic inches.
The Raymarine Type 2 Pump for Autopilots is a Reversing hydraulic pump for use with steering systems equipped with 14–21 cubic inch (230-350cc) hydraulic steering rams.
This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 20 Meter.
This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 3 Meter.
This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 9 Meter.
The Raymarine SeaTalk NG Cable Kit comes with all of the parts you need to start a Seatlk NG Network.
SeaTalk NG power cable to power your SeaTalk NG Network.
Raymarine's Seatalk NG Terminator is used to begin or end your Seatalk NG Network Backbone.