Raymarine Accessories

Raymarine's 5-Way Connector is designed to connect 3 drop cables and 2 terminators.

Raymarine SeaTalk Ng to DeviceNet (NMEA2000) Female Adapter Cable

Raymarine SeaTalk Ng to DeviceNet (NMEA2000) Male Adapter Cable 1M.

Network two Raynet devices together with the Female/Female Cable. Length 2M

Network two Raynet devices together with the Female/Female Cable. Length 5M

Raymarine Replacement Rudder Reference Transducer compatible with Raymarine and Autohelm autopilot systems.

The Raymarine STng (Male) to DeviceNet (Female) snap-on spur adaptor allows for easy connection to NMEA2000 devices.

This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 400mm.

This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 5 Meter.

Connect two standard Raynet cables together with the Male to Male Cable Joiner. Length 50mm

Raymarine Converter kit allows select SeaTalk 1 devices to interface and communicate on the SeaTalk NG data network. Plug and Play insallation.

The Raymarine SeaTalk NG Starter Kit includes all the pieces necessary to create a SeaTalk NG network on your boat.

Raymarine's Seatalk NG Terminator is used to begin or end your Seatalk NG Network Backbone.

The Raymarine ITC-5 converts analogue transducer signals for Speed/Temperature, Depth, Wind, Rudder Angle and Fluxgate Compass to SeaTalk NG eliminating the need for multiple ST70 Pods.

Raymarine's A80490 adapter cable is required for all CPT-S tranducers to connect to an Axiom RV, Axiom Pro S, Axiom 2 Pro S and an Axiom Pro RVX. 9 pin connection from CPT-S transducer will plug into the 25 pin connection on the MFD.

Pair the HV-100.02 Transom Mount transducer with your Raymarine element for excellent underwater images and water temperature. Using multiple frequencies of 200kHz/350kHz and 1.2Mhz this transducer will provide detail to 900' below your boat!  Replaces A80603.

Protect your Raymarine Element 9 from scratches and sun when not in use!

The Raymarine SeaTalk NG Spur Cable is used to connect individual devices to the SeaTalk NG backbone. The SeaTalk NG Spur Cable connects to a T-Connector.

The Raymarine RNS-5 network switch allows for easy expansion of Raymarine systems using RayNet high-speed Ethernet cabling. Need more than 5 ports? Two RNS-5 switches can be daisy-chained together for larger systems.

Raymarine's Raystar 150 10Hz replaces the RS130 and offers a GPS/Glonass Receiver that provides faster performance and enhanced accuracy. RS150 is SeaTalkNG Compatible and NMEA2000 Certified with optional devicenet adapter. Designed for Simple Surface Mounting.

Raymarine Short Arm Wind Vane for Wind Speed and Angle. Includes 30m cable. Compatible with i60, iTC-5, ST60+ and ST60.

Connect your Alpha Performance Display to a Raymarine Axiom Chartplotter using this single cable that serves as both power and data (Raynet). This single cable design means less cabling running through the deck and mast, resulting in a simple and fast installation!
Cable Length: 1M

The Raymarine EV-1 is an evolution autopilot sensor core for traditional steering systems. This intelligent EV sensor core monitors vessel motion in three dimensions.

The Raymarine RNS-8 is a network switch allowing for easy networking of your compatible Raymarine components. This 8 port Gigabit RayNet network switch includes 4 dedicated power-over-ethernet (POE) ports. Integrate Axiom displays with radars, sonar modules and FLIR thermal cameras with ease!

The Raymarine ECI-100 Universal Engine and Control Interface bridges engine instrumentation and drive-by-wire steering with Raymarine autopilot and navigation systems. This simple, single point of connection integrates Raymarine’s latest generation of MFD’s and provides autopilot steering interface to Evolution EV-2 Drive by Wire autopilots.

Raymarine's RCR-1 USB microSD card reader provides remote microSD access to Axiom, Axiom+, Axiom Pro, Axiom Pro 2, and Axiom XL chartplotter displays. Designed to make accessing the microSD card slot easier, The RCR-1 is recommended for Axiom and Axiom+ installations when the rear microSD card reader is not readily accessible. Axiom XL installations require an RCR-1 or RCR-SD USB for microSD card access.

Raymarine SeaTalk HS Dual End Weatherproof Network Cable 1.5M

Raymarine Seatalk High Speed 1.5m Cable

Raymarine Seatalk High Speed 5 Meter Cable

The Raymarine Masthead System provides accurate wind speed and direction. Includes Masthead only. Compatible with ST60+.

Raymarine RayNet to SeaTalk HS Network Cable 1 Meter

Raymarine RayNet to SeaTalk HS Network Cable 3 Meter.

Raymarine RayNet to SeaTalk HS Network Cable 10 Meter

The Raymarine SeaTalk NG Cable Kit comes with all of the parts you need to start a Seatlk NG Network.

Raymarine 3M SeaTalk Interconnect Cable

Raymarine Adapter cable for DSM300 to DSM25. Allows the A-Series fishfinders (DSM25) to work with the Digital Sounder Module (DSM30/300) series transducers

This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 1 Meter.

This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 3 Meter.

This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 20 Meter.

This Raymarine Cable is used as your SeaTalk NG Backbone Cable. Length 9 Meter.

3 Meter Transducer extension cable for your DSM30/300.

5 Meter Transducer extension cable for your DSM30/300.

Network two Raynet devices together with the Female/Female Cable. Length 10M

Network two Raynet devices together with the Female/Female Cable. Length 20M

Raymarine SeaTalkNG T-piece connector.

This cable is used to connect units with RayNet networks to speak with units with SeaTalk HS networks.

SeaTalk NG power cable to power your SeaTalk NG Network.

Intergrate NMEA2000 components with a SeaTalkNG backbone with the T12217 cable kit.