Installation Products

Don't drill holes in your transom! Stern Saver keeps your transom free of transducer mounting bracket holes. The included adhesive creates a bond between the polyethylene block and the fiberglass of your boat.

The Single Arm Holding Wrench fits the B164 and B175/SS175 transducers and assists with installation. This wrench fits on the top of the transducer and holds it in place during installation. This wrench can be used in tandem with the Single Arm Wrench or Double Arm Wrench.

Scanstrut’s smallest wireless phone charging mount! The Scanstrut Nano is a 10W waterproof wireless charger that holds your phone securely while charging it. This ultra-compact design can be installed and used in any orientation.

The Single Arm Wrench fits the B164 and B175 transducers and assists with installation. The Single Arm Wrench can be used in tandem with the Single Arm Holding Wrench.

The Shakespeare gold plated brass PL-258-CP-G joins two cables together in a snap. No stripping or soldering required. For RG-8X or RG-58/AU coax cable. Barrel connector for PL-259-ended cables.

PropSpeed's FoulFree Transducer Coating Kit is the biggest advancement in transducer paint and coatings in the last 30 years. It will keep your thru-hull or transom mount transducer free of marine growth. This nontoxic formula has zero leaching of harmful chemicals into water unlike traditional anti-fouling bottom paints and is certified by Airmar.

The Seaview Modular Aft Mount and Plate with Light Bar Bundle includes the standard Seaview 5" Aft Raked Modular Radar Mount Base, Seaview Modular Plate for Dome Radars, Seaview Light Bar and the Seaview Combination Mast Head All Around LED Light.

The Navico Ethernet Adapter Cable Green M12M 8-pin - Yellow 5-pin female (1.2 ft) works to adapt yellow ended ethernet cables to the NEP-3 port expander.

The Shakespeare DORSAL VHF antenna is designed specifically for greater effectiveness in short-range applications. The fully water sealed body is durable for longtime use and the fin design prevents the antenna from getting snagged. Suitable for up to 10 mile range. Color: White.

The Garmin LiveScope Bulkhead Connector Kit allows you to flush mount your LiveScope extension cable for easy connection/disconnection of your LiveScope transducer.

Extend the cable length of your Garmin Panoptix LiveScope LVS32, LVS34 or XR LVS62 transducer with this extension cable. Cable is 30 feet long (9 meters).

Convert NMEA 0183 data into NMEA 2000 data and vice versa allowing them to talk and listen to each other. The NGX-1-ISO is equipped with a bare wire open ended cable, allowing for connectivity to an NMEA 0183 device, or Serial Port / DB-9.

The Raymarine RNS-5 network switch allows for easy expansion of Raymarine systems using RayNet high-speed Ethernet cabling. Need more than 5 ports? Two RNS-5 switches can be daisy-chained together for larger systems.

The Garmin marine network adapter cable converts small (male) network cable to a large network connector in order to connect to your compatible Garmin chartplotter.

The Double Arm Wrench fits the B164 and B175 transducers and assists with installation. The Double Arm Wrench can be used in tandem with the Single Arm Holding Wrench.

The SiTex AIS Zero Loss Antenna Splitter Module allows for full use of VHF communications and AIS send/receive with a single VHF antenna. The MDA-3 is designed for use with Class B AIS Transceivers.

The Seaview Vertical Mount includes an 8" diameter, King Starboard base plate specifically designed for use with the Sionyx Nightwave camera. The raised mount is durable and corrosion resistant.

Stainless Steel Clam Shell, Large 2.25" W x 2.25" L

The Seaview 4-Degree Base Wedge fits mount base dimensions of 7" x 7". This wedge features pre-drilled mounting holes that allow for quick and easy installation and are made from a marine-grade polymer.

Si-Tex Hydraulic Autopilot Hose Kit with Fittings, Part Number OC17SUK42.

The Shakespeare 6187 is a full 4D range of motion ratchet mount that provides maximum mounting location flexibility. The 6187 can be installed at extreme angles and is made of stainless steel.

Protect your motor and blade from impact with the skeg for Force Kraken trolling motors.
Select Color Below.

Network compatible Garmin devices with the 6 foot BlueNet Marine Network Cable.

The 60A Garmin Circuit Breaker is used when installing a compatible Force Trolling Motor.

Extend your Garmin 6-pin transducer cable 10 feet with the Airmar Transducer Extension Cable.

The Raymarine ECI-100 Universal Engine and Control Interface bridges engine instrumentation and drive-by-wire steering with Raymarine autopilot and navigation systems. This simple, single point of connection integrates Raymarine’s latest generation of MFD’s and provides autopilot steering interface to Evolution EV-2 Drive by Wire autopilots.

Almo Wire's 14 Gauge 2 Conductor wire comes in a 100' spool. The exterior plastic housing is white in color and the internal wires are Red and Black. Perfect for wiring your GPS, Fishfinder, VHF Radio or other piece of Marine Electronics.

Almo Wire's 14 Gauge 2 Conductor wire comes in a 250' spool. The exterior plastic housing is white in color and the internal wires are Red and Black. Perfect for wiring your GPS, Fishfinder, VHF Radio or other piece of Marine Electronics.

Almo Wire's 16 Gauge 2 Conductor wire comes in a 100' spool. The exterior plastic housing is white in color and the internal wires are Red and Black. Perfect for wiring your GPS, Fishfinder, VHF Radio or other piece of Marine Electronics.

Almo Wire's 16 Gauge 2 Conductor wire comes in a 250' spool. The exterior plastic housing is white in color and the internal wires are Red and Black. Perfect for wiring your GPS, Fishfinder, VHF Radio or other piece of Marine Electronics.

The Garmin Verado Adapter Kit is used for plumbing your Garmin Hydraulic Autopilot to your Mercury Verado Engine Steering System.

The Garmin SeaStar Fittings Kit is used for plumbing your Garmin Hydraulic Autopilot to most SeaStar Steering System.

The Seaview Small Grey plastic cable seal is designed to work with currently installed cables and provides a waterproof seal without removing and rerunning the cables! 

The Seaview Large Grey Plastic Cable seal with split seal design allows for waterproof cable routing without removing connectors!

Ultra heavy duty mast mount designed with adjustable rails to make sure your radar can be mounted as close to your mast as possible. Compatible with many 24-inch radar domes.

The Seaview Small Polished Stainless Steel Cable seal with split seal design allows for waterproof cable routing without removing connectors!

The Seaview Large Stainless Steal Cable Seal with split seal design allows for waterproof cable routing without removing connectors!

The Seaview Multiple Cable Seal comes in grey plastic with split seal design and allows for waterproof cable routing for up to 3 cables without removing connectors!

The Seaview Multiple Cable Seal comes in Black Powder Coated Stainless Steel with split seal design and allows for waterproof cable routing for up to 3 cables without removing connectors!

The Seaview 4-Degree Base Wedge fits mount base dimensions of 10" x 10". This wedge features pre-drilled mounting holes that allow for quick and easy installation and are made from a marine-grade polymer.

The Shakespeare 3187 Stainless Steel Ratchet Mount is a versatile mount with a four-way ratchet design. Designed for both vertical or horizontal mounting in mind! The 3187 mount fits standard 1"- 14 threads and features a cable slot for easy installation.

Updating your Garmin multifunction display has never been easier. Flush mount a GPSMAP 12x3 into the existing cutout of a GPSMAP 12x2 Touch, 12x2 Plus, 7412 or 7612 chartplotter using this Garmin adapter plate. 

Updating your Garmin multifunction display has never been easier. Flush mount a GPSMAP 9x3 into the existing cutout of a GPSMAP 9x2 or 9x2 Plus using this Garmin adapter plate. 

Updating your Garmin multifunction display has never been easier. Flush mount a GPSMAP 7x3 into the existing cutout of a GPSMAP 7x2 or 7x2 Plus using this Garmin adapter plate. 

The Scanstrut Flip Pro is 12V or 24V input and is equipped with 1 Type A and 1 Type C port, providing options in the best connection and power for your device. The Flip Pro is small in size, IPX4 waterproof rated and includes a protective cap that springs closed and locks open when charging.

The Scanstrut Flip Pro with front fit bezel is 12V or 24V input and is equipped with 1 Type A and 1 Type C port, providing options in the best connection and power for your device. The Flip Pro is small in size, and easy to install with the included front bezel. This mounting style is idea if you are unable to gain access to behind panels. IPX4 waterproof rated and includes a protective cap that springs closed and locks open when charging.

The Shakespeare DORSAL VHF antenna is designed specifically for greater effectiveness in short-range applications. The fully water sealed body is durable for longtime use and the fin design prevents the antenna from getting snagged. Suitable for up to 10 mile range. Color: Black.

The Seaview PM5SL8 Vertical Mount will raise your compatible thermal camera or searchlight 5.5"-5.75". The small, 8-inch diameter base takes up minimal space, making it an ideal solution for installations where space is limited.